Sheet 402 004 Drawing archive

Engineering Workshop Terms: A Glossary of Manchester's Mill Trades

Wage books, census returns and works letters use job titles and shop words that nobody explains. This glossary decodes 34 of them, from the foundry floor to the spinning room.

Terms explained
34
Trades covered
Foundry, works, mill
Whitworth thread
1841, 55 degrees
Mule team
Minder and two piecers
Engraved illustration of a Victorian machine shop with a lathe in the foreground, overhead line shafting and belts
Fig. 1 / WORKSHOP GLOSSARYSheet 402
On this sheet / 5 parts

Census enumerators wrote down what people told them, and people told them their trade in the words of the shop. A great-grandfather listed as a holder-up in 1881, or a girl of thirteen entered as a little piecer, makes sense only if you know the vocabulary. The engineering workshop terms on this page come from three overlapping worlds that met in Manchester: the foundry, the machine shop and erecting shop, and the cotton mill. Most of them also turn up in works letterbooks and on the drawings described in the drawing archive.

How the trades fitted together

A Victorian engineering works was a chain of separate trades, each with its own skills and its own status. The drawing office produced the design. The patternmaker turned the drawing into a wooden pattern. The moulder packed sand round the pattern to make a mould, the core maker formed the sand cores that left holes and passages, and iron melted in the cupola was poured in. The fettler then cleaned up the casting before it went to the machine shop, where turners and fitters brought it to size. Finally the erecting shop assembled the machine.

Boiler work ran alongside, with its own hierarchy. A hot riveting gang needed four people: a heater, often a boy, who warmed rivets in a small furnace and tossed them across; a catcher who caught each one and pushed it into the hole; a holder-up who pressed a heavy dolly against the head; and the riveter who closed the other end. Anyone who has read a wage book from a boiler shop will recognise those titles and the very different rates of pay beside them.

The millwright stood at the start of it all. Before the steam engine, millwrights were travelling craftsmen who designed and built mills, waterwheels and gearing, skilled with axe, hammer and plane. William Fairbairn, whose Manchester firm became one of the great names of the trade, began as one. As iron replaced timber, the millwright's broad skills split into the specialised trades of turner, fitter and machine maker, and mechanical engineering grew out of that division.

The glossary

TermMeaningWhere you'd hear it
PatternmakerCraftsman who made wooden patterns from drawings, allowing for the metal's shrinkage as it cooledPattern shop of a foundry or works
MoulderMade sand moulds from patterns, ready for pouringFoundry floor
Core makerFormed sand cores in a core box to create holes and passages inside a castingFoundry core shop
CupolaUpright shaft furnace for melting iron in direct contact with coke, with air blown in near the baseIron foundry
FettlerCleaned castings: removed sand, runners, risers, seams and finsFoundry fettling shop
TupThe heavy ram of a drop or power hammer, which carries the upper die and delivers the blowForge and smithy
SmithyBlacksmith's shop, where iron was forged by hand or under a hammerEvery works and mill yard
MillwrightOriginally a builder of mills, wheels and gearing; later a fitter who maintained shafting and mill machineryMills and engineering works
TurnerMachinist who shaped metal on a latheMachine shop
FitterFinished and assembled parts by hand and machine, to fit together preciselyFitting and erecting shops
Erecting shopWhere a complete machine or locomotive was assembledLocomotive and engine works
LatheMachine that rotates the work against a cutting toolMachine shop
Slide restTool-holding carriage of a lathe that moves the cutting tool along the work under controlMachine shop
Whitworth thread (BSW)Screw thread standard proposed by Joseph Whitworth in 1841, thread angle 55 degreesDrawings, stores, machine shop
GaugeA tool for checking a dimension, such as a thread or bore; also the distance between railsInspection, toolroom, railway
DraughtsmanPrepared designs and drawings in the drawing officeDrawing office
TracerCopied pencil drawings in ink onto tracing cloth, ready for printingDrawing office
BlueprintContact copy of a tracing: white lines on Prussian blueShop floor, drawing office
Works numberSerial number given to each machine or locomotive builtOrder books, maker's plates
Boiler-makerSkilled tradesman who shaped, assembled and riveted boiler platesBoiler shop
Rivet heaterHeated rivets in a small furnace and threw them to the catcher; often a boyBoiler shop, bridge and ship work
CatcherCaught the hot rivet, usually in a bucket, and placed it in the holeRiveting gang
Holder-upHeld a heavy dolly against the rivet head while it was closedRiveting gang
MuleSpinning machine combining rollers and a moving carriage; Samuel Crompton, 1779Spinning mill
JennyEarly multi-spindle spinning machine by James Hargreaves, 1764-1765; the name is probably short for engineEarly spinning
MinderSkilled spinner in charge of a pair of mulesSpinning room
PiecerRejoined broken threads on the mule; a team had a side piecer and a little piecerSpinning room
ScavengerChild who crawled under a stopped mule to clean dirt and oil from the mechanismSpinning room
DofferRemoved full bobbins or spindles of yarn and replaced them with empty onesSpinning and doubling mills
BobbinSpool on which yarn is woundThroughout the mill
OverlookerForeman over a room or a group of machines; an underlooker could hope for promotionSpinning and weaving
TacklerSupervisor who kept a set of power looms running and oversaw the weaversWeaving shed
Knocker-upWoke workers for their shift by tapping on windows with a poleStreets of mill towns
Cotton wasteShort fibre and trimmings left over from spinning; spun again into coarse yarn by condenser mulesWaste mills and dealers

Apprenticeship and the ladder

Entry to the skilled trades was through apprenticeship, and the engineering workshop terms an apprentice picked up first were the names of the people above him. The ladder could be climbed. James Nasmyth, who later built the Bridgewater Foundry at Patricroft from 1836, started in 1829 as an assistant workman in Henry Maudslay's London works at 10 shillings a week, and was later employed there as a draughtsman. The shop floor and the drawing office were not sealed off from each other, and many draughtsmen came up through the shops.

Evening study helped. The Manchester Mechanics' Institution was set up in 1824 by a group of the town's businessmen, modelled on the London body that became Birkbeck, and offered classes to working men. Its line runs through to UMIST and from there into the University of Manchester. In 1868 Joseph Whitworth, himself a former apprentice, endowed the scholarships that still carry his name, intended to help apprentices and technicians reach academic engineering. The Institution of Mechanical Engineers administers them today.

Mill children had a harder start. A scavenger worked under moving machinery, and a little piecer's job was to rejoin broken ends all day. The step up was to side piecer and then to minder, which brought better pay and a team of one's own. Mule spinning also carried a health cost that only became clear late: around 1900 former cotton mule spinners showed a high rate of scrotal cancer, linked to the mineral oil that misted from the spindles onto their clothing. Regulations in the 1920s limited the oils allowed, by which time the cotton mule was already being replaced.

Talk of the shop floor

Many engineering workshop terms travelled beyond the trades. Fettle, in northern speech, means to put something right, and in fine fettle survives in standard English. The tackler gave his name to a body of Lancashire humour, the tacklers' tales, in which he is gullible and slow; Geoffrey Mather collected them in a book in 2003. A tackler would probably have pointed out that a weaving shed full of looms stopped without him.

The knocker-up was a street figure rather than a works trade, but belonged to the same world. Alarm clocks were neither cheap nor reliable, so mill and works hands paid someone to tap on the bedroom window with a long pole. Large numbers worked in Manchester, and a few were still at it in parts of industrial England into the early 1970s.

Some terms changed meaning over time, which is a trap for family historians. A millwright in 1790 designed whole mills; a millwright in 1920 was more likely a maintenance fitter looking after the shafting. A gauge on a locomotive drawing usually means the track gauge, while in the toolroom it means a measuring tool. Joseph Whitworth's insistence on standard threads and accurate gauges, set out from his Manchester works from 1841 onward, is one reason a bolt made in one shop could be expected to fit a nut made in another, and why BSW turns up so often on drawings read with the help of the general arrangement guide.

Where the words survive

The best places to meet these engineering workshop terms in context are works records: wage books, letterbooks and order books held in record offices, listed in the drawing archive. Census returns from 1841 onwards give occupations in the enumerator's spelling, so expect variation. Trade directories add the masters' side, listing patternmakers, boiler-makers and millwrights with their addresses.

For the mill vocabulary, a working mule at Quarry Bank in Styal, built by Samuel Greg in 1784 and run today by the National Trust, shows what a minder and his piecers were dealing with. Reading about the cotton mills of Ancoats adds the city setting. The machinery explains the words faster than any table, because a doffer's job makes sense the moment you watch a full bobbin come off a spindle.

Questions readers ask.

Notes / 05
Q01

What did a fettler do?

In a foundry, a fettler cleaned up castings after they came out of the mould: knocking off sand, cutting away the runners and risers where the metal had been poured, and grinding off seams and fins. The work was heavy, noisy and dusty. In northern speech the verb fettle also means to put something in order or repair it.

Q02

What was a tackler in a cotton mill?

A tackler was a supervisor in a weaving shed who looked after a set of power looms and the weavers working them. The name comes from tackling the mechanical faults on the looms. Tacklers were almost always men, and Lancashire humour made them the butt of a long series of jokes known as tacklers' tales.

Q03

What is a knocker-up?

A knocker-up was paid to wake workers in time for their shift, before cheap alarm clocks. Tools included a long pole for tapping on upstairs windows and, in some cases, a pea-shooter. Knocker-ups worked in industrial towns including Manchester, and the job survived in a few places in England until the early 1970s.

Q04

What is the difference between a doffer and a piecer?

A doffer removed full bobbins or spindles of spun yarn from a spinning frame and replaced them with empty ones. A piecer worked on a spinning mule, rejoining threads that broke as the carriage moved. A pair of mules was run by a minder with two piecers, the side piecer and the little piecer, who was often a child.

Q05

What does BSW mean on an engineering drawing?

BSW stands for British Standard Whitworth, the screw thread that Joseph Whitworth of Manchester proposed in 1841. It was the first national screw thread standard in the world, with a thread angle of 55 degrees. British railway companies adopted it in place of their own bolt and thread standards, and it appears on drawings for more than a century.